Samsung Digimax S MP Digital Camera Manual · Konica Minolta magicolor Abit AN8 Series Manual · Abit AN8 SLI Manual · Abit AN9 32X Manual. CPU. Supports Socket Athlon64/ 64FX/ 64X2 Processor with 2GHz system bus using Hyper Transport™ Technology; Supports AMD CPU Cool ‘n’ Quiet. ABIT AN8 32X – motherboard – ATX – Socket – nForce4 SLI overview and full product specs on CNET.
|Published (Last):||22 September 2007|
|PDF File Size:||15.53 Mb|
|ePub File Size:||14.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
No part of this manual may be reproduced, transmitted or transcribed without the expressed written permission of the manufacturer and authors of this manual.
If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail, we cannot guarantee any responsibility. Table of Contents Chapter 1. Install Graphics Card s Hardware Setup Chapter 2. Hardware Setup Before the Installation: Failing to do so may cause the motherboard components or add-on cards to malfunction or damaged. Place the heatsink and fan assembly onto the socket. Match the heatsink clip with the socket mounting lug.
Hook the spring clip to the mounting lug. On the other side, push the retention clip 8. Attach the four-pin power plug from the straight down to lock into the plastic lug on the heatsink and fan assembly to the CPU FAN retention frame.
For detailed information on how to install your heatsink and fan assembly, please refer to the instruction manual that came packed with the Hardware Setup CrossFire Mode: To enable CrossFire Mode, you will need to: Download the latest driver from ATI website www. Connectors, Headers and Switches Here we will show you all of the connectors, headers and switches, and how to connect them. Please read the entire section for necessary information before attempting to finish all the hardware installation inside the computer chassis.
These fan connectors are not jumpers. DO NOT place jumper caps on abitt connectors. Hardware Setup 4. Connects to the Suspend LED cable if there is one of chassis front panel.
Connects to the Power Switch cable of chassis front panel. Connects to the Power LED cable of chassis front panel. Hardware Setup 7.
ABIT AN8 32X Manuals
Disable wake-up function support at USB1 port. Pin shorted default: Enable wake-up function support at USB1 port. The red line on the ribbon cable must sn8 aligned with pin-1 on both the IDE port and the hard-drive connector. Hardware Setup 9. Hardware Setup POST Code in address 80h to find out where the problem lies.
Connects to the front left and front right channel in the 7. Connects to Local Area Network. Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc.
In order to increase system stability and performance, our engineering staffs are constantly improving the BIOS menu. Manuao BIOS setup screens and descriptions illustrated in this manual are for your reference only and may not manusl match what you see on your screen. This item displays the processor speed of the CPU installed on this motherboard.
You can also select the [User Define] option to enter the manual option. The wrong settings of the multiplier and external clock in certain circumstances may cause CPU damage. Exit These items display the power cycle statistics for each element. These items set the high and low voltage limit. The value of high limit must be set above the one nanual low limit. This item sets the high and low temperature limits desired for the fan speed control. This item sets the high and low voltage limits for the fan.
This item displays the approximate capacity of the disk drive. Usually the size is slightly greater than the size of a formatted disk given by a disk-checking program.
This item configures the number of cylinders. This item displays the number of cylinders at which to change the write timing. This item configures the number of sectors per track. When this a8 is set to Enabled, if the BIOS detects no floppy drive, it abt display a floppy disk drive error message. If this item is disabled, the BIOS will skip this test. The default setting is Disabled.
This item determines the default state of the numeric keypad at system booting up. The numeric keypad functions as number keys. The numeric keypad functions as arrow keys.
ABIT AN8 32X User Manual
This item determines when the system will prompt for password – every time the system boots or only when it enters the BIOS setup. This item selects the DRAM timing mode. The an88 may be unstable or unable to boot up if your DRAM module does not support the clock you set. Select [Disabled] if you want to add a different hard drive controller.
This option enables or disables the on-chip Maanual controller. This item selects the SATA mode. Refer to the following table for the relationship among different configurations over the SATA connectors. This option enables or disables the IEEE controller. Back to Integrated Peripherals Setup Menu: Two options are available: The default setting is Enabled. You can enable or disable the onboard FDC controller. BIOS Setup This option protects the BIOS configuration or restricts access to the computer itself.
Install Audio Driver Appendix A. Install Audio Driver The installation procedures and screen shots in this section are based on Windows XP operating system. For those of other OS, please follow its on-screen instruction. The installation for USB 2. CD to enter the installation menu. The following screen appears. Choose [Yes, I want to restart my computer now. Build MP table 2.
Set CMOS century to 20h or 19h 4. Start power on sequence 8. Enable ATX power supply 8. ATX power supply ready 8. DDR voltage ready 8. Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please move the CMOS jumper from its default position to for a few seconds, and abif back.
Abit AN8 32X Manuals
Write down the sound card model, aan8 model, BIOS identification number on the technical support file refer to main instructionsand describe the problem in the space provided. Motherboard model number REV: Technical Support Form Company Name: Also please make sure you have the latest drivers from your peripheral card makers! We are trying to expand and make the FAQs more helpful and information rich.
Let us know if you have any suggestions. They should have reasonable return or refund policies. How they serve you is also a good reference for your next purchase. First, please contact manuak support team for the branch office closest to you. Please contact the reseller from whom you bought the product. You should be able to get RMA service there. Because of tremendous number of email messages we receive every day, 3x are forced to give greater weight to certain types of messages than to others.
Page of 80 Go. Page 58 Page 59 – Appendix D.