ATMEL 24C04 PDF

ATMEL 24C04 PDF

each, the 16K requires an bit data word address for random word addressing. WP Pin. Status. Part of the Array Protected. 24C01A. 24C 24C 24C08A. 24C04 EEPROM are available at Mouser Electronics. Mouser offers For: 24C Obsolete. Microchip Technology / Atmel, EEPROM 7 MILS V – 10MS V. Read about ’24C04 Interfacing issue’ on elementcom. Hey there,I am trying to interface the AT24C04 4K EEPROM with Atmega

Author: Gajin Miramar
Country: India
Language: English (Spanish)
Genre: Education
Published (Last): 14 March 2010
Pages: 258
PDF File Size: 14.44 Mb
ePub File Size: 15.92 Mb
ISBN: 440-5-66994-601-3
Downloads: 94246
Price: Free* [*Free Regsitration Required]
Uploader: Vilar

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. However, it doesn’t matter what I set these pins to.

Amtel output is from I2C scanner.

Is there something else I need to do? Are you being confused by the common mistake that many people make where they treat afmel address of an I 2 C wrongly? Even the data sheet that you linked can lead to confusion in this regard. In figure 4 they refer to the address as an 8-bit quantity:.

Also be aware that amtel A0 to A2 pins on the device package are meant to remain static in a design. If a total of eight 24C02’s are used in the design then each of the devices will have these three pins hard strapped in a different combination from the set of b, b, b, b, b, b, b and b.

24c04 Read & Write

When you say that you are “writing” to the pins this does not make clear exactly what you are doing. Normally there is no writing to the 24C02 pins. Instead the three bits that you supply out on the interface in the device address field must match the hard strapped values on the pins in order for the device to be selected. On top of that I armel never been sure that it is even possible to dynamically change the strapped value on the A0, A1 and A2 pins of a atmle after it has powered up.

  LG INTELLOWASHER 7KG WD 8015C MANUAL PDF

A2 atmrl used for creating the address. The device will not respond to the address that is being set dynamically. It considers the value of the A0,A1 and A2 before the power up and sticks to it till reset.

By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

10pcs At24c04 24c04 Serial EEPROM Sop-8 ATMEL

Home Questions Tags Users Unanswered. Found 8 device s.

Check your chips markings. You do not write the addresses; you hardwire them. TurboJ The chip says the following: Can you explain what hardwiring is?

In figure 4 they refer to the address as an 8-bit quantity: In Arduino, the function that does this is digitalWrite. That’s why I said “write”. If you just have one 24C02 then you would connect all three of those pins to GND as b. Then when you want to write to the part use an address byte of 0xA0 and when you want to read use an address byte of 0xA1. Then the address byte that you use to write to the atme chip would be 0xA2 and the address byte for reading the second chip would be 0xA3.

  APOLOGIA DELLA STORIA MARC BLOCH PDF

Then the address byte that you use to write to the third chip would be 0xA4 and the address byte for reading the second chip would be 0xA5.

Let’s build a toy Thumb Drive!

Can’t change the values dynamically. It will answer to address that was set up before powering up. So for example you keep A0: MaNyYaCk 6 Can you give more information?

But my suggestion would to directly connect them to ground or VCC for the addressing scheme. Maybe the issue is setting the address after power on. I will try in about an hour.

Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name.

Email Required, but never shown. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued stmel of the amtel is subject to these policies.