DRYPIX 4000 SERVICE MANUAL PDF

DRYPIX 4000 SERVICE MANUAL PDF

HANDLING THIS SERVICE MANUAL About This Service Manual n. Scope This Service Manual applies to the Fuji Medical Dry Laser Imager DRYPIX Service Technicians PACS / DR / CR / Digital Forum Drypix Service Manual CARLOS RUEDA Innovacion Tecnologica Hello, I am trying. View and Download FujiFilm DRYPIX service manual online. DRYPIX Printer pdf manual download.

Author: Junris Dousida
Country: Barbados
Language: English (Spanish)
Genre: Business
Published (Last): 10 February 2010
Pages: 12
PDF File Size: 3.80 Mb
ePub File Size: 5.59 Mb
ISBN: 965-7-82740-112-9
Downloads: 85024
Price: Free* [*Free Regsitration Required]
Uploader: Mokree

The screws painted in yellow must be adjusted dryix the installation of parts. When installing parts, this is indicated if alignment to the boss is required.

FujiFilm DRYPIX 7000 Service Manual

EPS SP Steps that differ between the three units are indicated separately. Removing Procedure Remove the following covers. MC Remove the tray inside cover. Reinstalling Procedure Reinstall in the reverse order of removal. MC Remove the tray. However, there is no need to pull out the rail pushed into the equipment. EPS Reinstall in the reverse order of removal.

Tray lock assembly Back side FP7C Inner slide rail FP7C EPS Remove the tray loading unit rail. Place the tip in front and behind the right rail of the tray loading unit on the aperture of the tray loading unit, tighten the rail temporarily with the screws.

When removing the squeezing roller, be careful not to damage the bearing of the tray, Remove the squeezing roller. Remove the special screws. Secure the gear while pressing the flange of the idle gear against the gears in the arrow direction shown below. Remove the gear 1 and gear 2. Insert pins such as hexagonal wrench into the two holes on gear 1, and adjust the phase of the removal drive cam.

EPS Secure the gear fixing cover with the screws. Secure the cable with the clamp. MC Remove the suction cup arm. EPS Change the attaching position of the film release plate.

To return the film size from 20 x 25 cm to other sizes, refer to the following figure and change the attaching position of the film release plate. Remove the suction cup arm.

Push down the plate, and with an approximately 50 mm space between the plate and stopper, push the suction cup against the film. Two minutes later, check that the space is still 50 mm. Remove the following covers. If the equipment mounts film tray 2, loosen the screws securing the idle gear of the middle conveyor unit. MC Remove the sub-scanning unit fixing bracket. EPS Reinstall the sub-scanning unit fixing bracket at the position shown below.

  ARCHEXTERIOR VOL 14 PDF

MC Remove the screws securing the sub-scanning unit. EPS Remove the upper conveyor unit removing jig. Rotate the worm gear of the cleaning roller grip release motor MD4 in the arrow direction shown in the figure with the hand so that it grips the cleaning roller. Remove the grip position detection sensor bracket. Remove the connector bracket.

Remove the film positioning assembly lower. Remove the upper conveyor unit. Open the left and right positioning guides until they touch the sides when installing the film positioning motor MD5. EPS Remove the upper conveyor unit. Remove the conveyance driving roller lower.

Remove the lower conveyor unit. Remove the sub-scanning unit fixing bracket.

Fujifilm – DryPix Community, Manuals and Specifications | MedWrench

MC Reinstalling Procedure Insert the sub-scanning unit into the equipment, and temporarily secure with the screws. Remove the sub-scanning unit fixing bracket, and reinstall it to its original position. MC If the measured values are not the specified values, loosen the screws securing the sub-scanning unit. Rotate the positioning screw in the clockwise or counterclockwise direction and adjust.

EPS If the measured values are not the specified servlce, adjust the film conveyance amount.

Remove the belt cover. Remove the SUS belt. Reinstall in the reverse order of removal. Removing Procedure Insert the shutter into the film tray. MC Reinstall the sub-scanning unit fixing bracket at the position shown below. However, perform the following when securing the sub-scanning unit into the equipment. Insert the sub-scanning unit into the equipment, and temporarily secure with the screws.

Rail of equipment FP7C EPS Remove the sub-scanning unit fixing bracket, and reinstall it to its original position.

When the data transfer is completed, the [File transfer is completed. Reboot the equipment, and start the M-Utility. Output the grid pattern using the M-Utility. MC Remove the cooling fan assembly. Remove the cooling fan assembly. Remove the filter section cooling fan. Remove the film release unit.

Remove the heat development unit. When reinstalling the adiabatic cover, do not sandwich the thermistor cable. MC Remove the film release unit. Press the LED cover of the density measurement light-emitting board against the position shown in the figure below, and secure. Remove the operation panel. Remove the PC board. Turn ON the power of the equipment, and start the M-Utility. Reinstalling Procedure There are three timing belts.

  FM BUGGER CIRCUIT PDF

Install the inside belt first and then the top and bottom belts. Loosen the fixing screws of the magnet. Close the jam removing guide plate, and tighten magnet fixing screws where it touches the stopper.

Turn ON the power of the equipment. Prepare the PC for servicing. When completed, [File Copy Finish!! When installation completed, the [Software Install Finish!! Shutdown the PC for servicing. Disconnect the network cable of the PC for servicing from the network to which the equipment is connected.

When the data copy is completed, the [FD File transfer is completed. Page of Go.

Drypix Service Manual – Service Technicians Forum

Table of Contents Add to my manuals Add. Fujifilm DryPix Specification 4 pages. Page 3 The screws painted in yellow must be adjusted after the installation of parts.

Table Of Contents MC 3. Tray Loading Unit Steps that differ between the three units are indicated separately. Page 16 MC Remove the tray inside cover. Page 18 Reinstalling Procedure Reinstall in the reverse order of removal.

Page 20 MC Remove the tray. Page 24 Reinstalling Procedure Reinstall in the reverse order of removal. Page 28 Place the tip in front and behind the right rail of the tray loading unit on the aperture of the tray loading unit, tighten the rail temporarily with the screws. Squeezing Roller When removing the squeezing roller, maanual careful not to damage the bearing of sevice tray, Remove the squeezing roller.

Page 39 Secure the gear while pressing the flange of the idle gear against ddypix gears in the arrow direction shown below. Removal Drive Cam Remove the gear 1 and gear 2. Page 42 Insert pins such as hexagonal wrench into the two holes on gear 1, and adjust the phase of the removal drive cam.

Page 46 MC Remove the suction cup arm.

Page 48 To return the film size from 20 x 25 cm to other sizes, refer to the following figure and change the attaching position of the film release plate.